FES Instructions for UK Time Change in Autumn 2021

FES Instructions for UK Time Change in Autumn 2021


Introduction 


On Sunday 31st October 2021 the clocks will be going back by 1 hour due to the end of Daylight Saving Time.


The purpose of this document is to ensure that all of your Mitrefinch units connected via a Fire Evacuation System (FES) are correctly updated with the adjusted time on Sunday morning. If you are unsure whether you have a FES System then an example screenshot is shown below: 












The time shown on all Mitrefinch units connected to a FES System is taken from the FES unit.  The instructions below explain how to setup FES to automatically adjust the BST time. 




Should you require any assistance or have any questions about the instructions then please contact Mitrefinch Support by emailing 
support@mitrefinch.co.uk or raise a ticket via our support portal website by clicking here.  Alternatively, please call 0330 726 0090.


How to enable the Time Change within FES

Please note that during steps 2, 3 and 4 your fire evacuation system will NOT be active, though it will catch up once you complete step 4. 

  1. On the FES unit, exit the current FES session by Pressing Crtl + F10 together then when prompted ‘Y’. This will take you to your DOS prompt. 
  2. Type IPMENU or (if using FES version 5.00 and above) enter MODMF at the command prompt then press Enter. This should load your Interactive Poller Utilities. 

If it does not, then type CD IPMF and press Enter.  Then type IPMENU or MODMF (depending on version) and press Enter. 

  1. In versions below 5.00 FES use the arrow keys and then ‘Enter’ key to select “System Parameters” and then “Miscellaneous details”.  Or if version 5.00 and above just select “Miscellaneous details”.  Then press page down twice and at the bottom of the screen under the section ‘BST changes’ it should contain two changes dates. Ensure that ‘Back’ (highlighted in the red box below) contains the date 31-10-2021:

Useful tip - In order to avoid having to perform this change again for the Spring 2022 time change, enter 27-03-2022 in the ‘Forward’ section as well.



  1. Press F1 to Accept and the Escape key until you return to the DOS prompt
  2. Then type IPMF to return back to the main FES screen. 

    • Related Articles

    • FES Instructions for UK Time Change in Spring 2023

      Introduction On Sunday 26th March 2023 the clocks will be going forward by 1 hour due to the BST Time change. The purpose of this document is to ensure that all of your Advanced units connected via a Fire Evacuation System (FES) are correctly updated ...
    • TMS Instructions for UK Time Change in Autumn 2021

      Introduction  On Sunday 31st October 2021 the clocks will be going back by 1 hour due to the end of Daylight Saving Time.  The purpose of this document is to ensure that all your Mitrefinch units are correctly updated with the adjusted time on Sunday ...
    • Spring Time Change - North America

      On Sunday March 10th 2019 the clocks will be going FORWARD by 1 hour as part of Daylight Saving Time. The purpose of this document is to ensure that all of your Mitrefinch Terminals are correctly updated with the adjusted time on Sunday morning. The ...
    • T&A Instructions for UK Time Change in Spring 2023

      Introduction On Sunday 26th March 2023 the clocks will be going forward by 1 hour due to the BST Time change. The purpose of this document is to ensure that all your Advanced units are correctly updated with the adjusted time on Sunday morning. The ...
    • TMS - European Working Time Directive Features

      The TMS Report Writer has a number of standard reports which are used to check that employees' work patterns comply with the EWTD. Please refer to the TMS User Guide, Chapter 21, for details on the directives upon which these new reporting features ...